LED Solar Floodlight with motion sensor VIDEX VL-FSO4-205-S is designed for autonomous lighting of open areas, parks, and residential surroundings. It is intended for installation on vertical walls and operates completely independently, powered by a solar panel. The built-in rechargeable battery is charged throughout the day by sunlight, allowing the floodlight to operate autonomously for up to 10 hours. This LED floodlight is ideal for use in locations where connection to the power grid is unavailable or limited. The key advantage of a solar-powered floodlight is zero electricity cost, along with the following benefits:

- High-quality LEDs provide bright, uniform, and directional lighting;
- Long service life without the need for maintenance;
- Built-in PIR motion sensor with a detection range of up to 8m and a 120° angle;
- IP65 protection rating, which makes floodlight suitable for all weather conditions.

Technical Specifications:
- Luminous flux – 1400Lm
- Color temperature – 5000K (daylight)
- Supports brightness adjustment (dimming)
- Color rendering index – Ra > 80
- Beam angle – 90°
- Battery type – LiFePO4, 3.2V, 5000mAh
- Battery capacity – 16Wh
- Solar panel – 6V, 6W
- Remote control (powered by CR2032 battery)
- Cable length – 2m
- Lifetime – 30000 hours
- Switching cycles – 20000
- Operating time – up to 10 hours
- Charging time – 5–8 hours (under direct sunlight)
- Charge/discharge cycles – 2000
- Recommended installation height – 3–4m
- Impact resistance – IK07
- Electrical protection class – III
- Warranty – 2 years

The set includes: a solar floodlight, a remote control, a CR2032 battery for the remote, mounting bolts, and a user manual. The total weight of the set is 1.09kg.

The product automatically turns on at night and switches off during daytime charging. The solar panel converts sunlight into electricity to charge the battery. Before first use, ensure the floodlight is fully charged for at least 8 hours in direct sunlight.

Turning the floodlight ON/OFF: 

1. To activate the floodlight, press the button on the housing once. The device will automatically switch to motion sensor mode.
2. To turn off the floodlight and switch it to sleep mode, press and hold the same button for 3 seconds.

REMOTE CONTROL:

Note: numbers correspond to button numbers. See the manual for details.

1. To turn on (ON) – press once to turn on.
2. To turn off (OFF) – press once to turn off. Double press to enter sleep mode. In this mode, the floodlight will not operate.
3. Maximum brightness – 100% brightness until the battery is discharged.
4. Half brightness – 50% brightness until the battery is discharged.
5. «+» button – increase brightness by 10%.
6. «-» button – decrease brightness by 10%.
7. «M» button – switch motion detection modes:
- PIR-A mode: the floodlight responds with two short flashes. It turns on at 100% brightness when motion is detected and dims to 10% after 15 seconds of no motion.
- PIR-B mode: press «M» again. The floodlight responds with three short flashes. It turns on at 100% brightness when motion is detected and turns off completely (0%) after 15 seconds of no motion.
In motion modes, brightness cannot be adjusted. Therefore, buttons 3, 4, 5, and 6 are disabled. To exit motion sensor mode, activate another mode using «AUTO», «3H», «5H», or «8H».
8. AUTO mode: activates automatic operation: first 3 hours – 100% brightness; 3–6 hours – 70% brightness; after 6 hours until switch-off or sunrise – 30% brightness. When this mode is activated, other modes, including the motion sensor, are disabled.
9. WAKE UP: after installation, press «WAKE UP» to activate the floodlight for first use. After that, the system will automatically charge and discharge.
10. 3H timer: operates at 100% brightness for 3 hours, then turns off automatically.
11. 5H timer: operates at 100% brightness for 3 hours, then 70% for the next 2 hours, then turns off automatically.
12. 8H timer: operates at 100% brightness for 3 hours, 70% for the next 3 hours, and 30% for the last 2 hours, then turns off automatically.
Thanks to the memory function, the selected cycle repeats daily.

Recommendations and safety precautions:

• Sleep mode is set by default by the manufacturer to prevent accidental activation during transportation. Press «WAKE UP» before first use.
• If the product is stored for a long time, switch it to sleep mode (double press «OFF»).
• Flashing red light indicates charging, while a steady red light indicates a full charge.
• Do not store the product with a discharged battery.
• The LED light source is non-replaceable. The battery may only be replaced by the manufacturer or an authorized service center.
• Dispose of used or damaged products in accordance with applicable regulations.